Schneider-Electric
ATV71LD33N4Z

Device short name: ATV71

Product destination: Asynchronous motors; Synchronous motors

Network number of phases: 3 phases

Supply voltage limits: 323…528 V

Supply frequency: 50...60 Hz - 5...5 %

Motor power kW: 15 kW, 3 phases at 380...480 V

Motor power hp: 20 hp, 3 phases at 380...480 V

Line current: 48 A for 380 V 3 phases 15 kW / 20 hp; 39 A for 480 V 3 phases 15 kW / 20 hp

Range of produc: Altivar Lift

Product or component type: Variable speed drive

Product specific application: Lift

variant: With integrated 7-segment display terminal

communication port protocol: Modbus; CANopen

[Us] rated supply voltage: 380...480 V - 15...10 %

EMC filter: Integrated

Apparent power: 31.6 kVA at 380 V 3 phases 15 kW / 20 hp

Prospective line Isc: 22 kA for 3 phases

Nominal output current: 33 A at 4 kHz 380 V 3 phases 15 kW / 20 hp; 27 A at 4 kHz 460 V 3 phases 15 kW / 20 hp

Maximum transient current: 44.9 A for 2 s 3 phases / 15 kW / 20 hp

Speed drive output frequency: 0…599 Hz

Speed range: 1…100 for asynchronous motor in open-loop mode, without speed feedback; 1…50 for synchronous motor in open-loop mode, without speed feedback; 1…1000 for asynchronous motor in closed-loop mode with encoder feedback

Torque accuracy: +/- 5 % in closed-loop mode with encoder feedback; +/- 15 % in open-loop mode, without speed feedback

Transient overtorque: 170 %, +/- 10 % for 60 s; 220 %, +/- 10 % for 2 s

Braking torque: 30 % without braking resistor; <= 150 % with braking or hoist resistor

Local signalling: 1 LED (red) for drive voltage

Output voltage: <= power supply voltage

insulation: Electrical between power and control

Type of cable: Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR; Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC; With an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC; With a NEMA Type1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC

Electrical connection: Terminal, clamping capacity: 2.5 mm², AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR); Terminal, clamping capacity: 35 mm², AWG 2 (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)

Tightening torque: 5.4 N.m, 47.7 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB); 0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)

Supply: Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 A, protection type: overload and short-circuit protection; Internal supply: 24 V DC (21…27 V), <200 A, protection type: overload and short-circuit protection

Sampling duration: 2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input(s); 2 ms +/- 0.5 ms (LI1...LI5) - discrete input(s); 2 ms +/- 0.5 ms (AI1-/Al1+) - analog input(s); 2 ms +/- 0.5 ms (Al2) - analog input(s)

Response time: R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for discrete output(s); R2A, R2B 7 ms, tolerance +/- 0.5 ms for discrete output(s); AO1 2 ms, tolerance +/- 0.5 ms for analog output(s); <= 100 ms in STO (Safe Torque Off)

Accuracy: +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C; +/- 0.6 % (AI2) for a temperature variation 60 °C; +/- 1 % (AO1) for a temperature variation 60 °C

Linearity error: +/- 0.15 % of maximum value (AI1-/Al1+, AI2); +/- 0.2 % (AO1)

Analogue output type: AO1 software-configurable voltage: 0...10 V DC, impedance: 470 Ohm, resolution 10 bits; AO1 software-configurable current: 0...20 mA, impedance: 500 Ohm, resolution 10 bits; AO1 software-configurable logic output 10 V 20 A

Discrete output type: Configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles; Configurable relay logic: (R2A, R2B) NO - 100000 cycles

Minimum switching current: 3 mA at 24 V DC for configurable relay logic

Maximum switching current: 5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (R1, R2); 5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (R1, R2); 2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1, R2); 2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1, R2)

Discrete input type: Programmable (LI1...LI5)24 V DC, with level 1 PLC - 3500 Ohm; Switch-configurable (LI6)24 V DC, with level 1 PLC - 3500 Ohm; Switch-configurable PTC probe (LI6) - 0…6 probes - 1500 Ohm; Safety input (PWR)24 V DC - 1500 Ohm

Discrete input logic: Positive logic (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1); Negative logic (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1); Positive logic (LI1...LI5), < 5 V (state 0), > 11 V (state 1); Negative logic (LI1...LI5), > 16 V (state 0), < 10 V (state 1); Positive logic (PWR), < 2 V (state 0), > 17 V (state 1)

Dielectric strength: 3535 V DC between earth and power terminals; 5092 V DC between control and power terminals

Insulation resistance: > 1 mOhm 500 V DC for 1 minute to earth

Frequency resolution: Display unit: 0.1 Hz; Analog input: 0.024/50 Hz

Connector type: 1 RJ45 (on front face) for Modbus; 1 RJ45 (on terminal) for Modbus; Male SUB-D 9 on RJ45 for CANopen

Physical interface: 2-wire RS 485 for Modbus

Transmission frame: RTU for Modbus

Transmission rate: 9600 bps, 19200 bps for Modbus on front face; 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal; 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen

Data format: 8 bits, 1 stop, even parity for Modbus on front face; 8 bits, odd even or no configurable parity for Modbus on terminal

Type of polarization: No impedance for Modbus

Number of addresses: 1…247 for Modbus; 1…127 for CANopen

Option card: Communication card for Modbus TCP; Communication card for Fipio; Communication card for Modbus/Uni-Telway; Communication card for Modbus Plus; Communication card for EtherNet/IP; Communication card for DeviceNet; Communication card for Profibus DP; Communication card for Profibus DP V1; Communication card for Interbus-S; Communication card for CC-Link; Interface card for encoder; I/O extension card; Controller inside programmable card; Overhead crane card

Discrete input number: 7

Discrete output number: 2

analogue input number: 2

Analogue input type: AI2 software-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits; AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign; AI2 software-configurable current: 0...20 mA, impedance: 242 Ohm, resolution 11 bits

analogue output number: 1

Method of access: Slave CANopen

Asynchronous motor control profile: Voltage/frequency ratio - Energy Saving, quadratic U/f; Flux vector control without sensor, standard; Flux vector control without sensor, ENA (energy Adaptation) system; Voltage/frequency ratio, 5 points; Flux vector control with sensor, standard; Voltage/frequency ratio, 2 points; Flux vector control without sensor, 2 points

Synchronous motor control profile: Vector control without sensor, standard; Vector control with sensor, standard

Acceleration and deceleration ramps: S, U or customized; Linear adjustable separately from 0.01 to 9000 s; Automatic adaptation of ramp if braking capacity exceeded, by using resistor

Motor slip compensation: Automatic whatever the load; Not available in voltage/frequency ratio (2 or 5 points); Suppressable; Adjustable

Switching frequency: 1...16 kHz adjustable

Nominal switching frequency: 8 kHz

Minimum braking resistance: 7 Ohm

Network frequency: 47.5...63 Hz

Protection type: Overheating protection: drive; Thermal protection: drive; Short-circuit between motor phases: drive; Input phase breaks: drive; Overcurrent between output phases and earth: drive; Overvoltages on the DC bus: drive; Break on the control circuit: drive; Against exceeding limit speed: drive; Line supply undervoltage: drive; Line supply overvoltage: drive; Against input phase loss: drive; Thermal protection: motor; Motor phase break: motor; Power removal: motor

Pollution degree: 2 conforming to IEC 61800-5-1

IP degree of protection: IP20 on upper part without blanking plate on cover conforming to IEC 61800-5-1; IP20 on upper part without blanking plate on cover conforming to IEC 60529; IP21 conforming to IEC 61800-5-1; IP21 conforming to IEC 60529; IP41 on upper part conforming to IEC 61800-5-1; IP41 on upper part conforming to IEC 60529; IP54 on lower part conforming to IEC 61800-5-1; IP54 on lower part conforming to IEC 60529

Vibration resistance: 1.5 mm peak to peak (f= 3…13 Hz) conforming to IEC 60068-2-6; 1 gn (f= 13…200 Hz) conforming to IEC 60068-2-6

Shock resistance: 15 gn for 11 ms conforming to IEC 60068-2-27

Noise level: 60.2 dB conforming to 86/188/EEC

Relative humidity: 5…95 % without condensation conforming to IEC 60068-2-3; 5…95 % without dripping water conforming to IEC 60068-2-3

Ambient air temperature for operation: -10…50 °C (without derating)

Operating altitude: <= 1000 m without derating; 1000...3000 m with current derating 1 % per 100 m

Operating position: Vertical +/- 10 degree

product certifications: C-Tick; CSA; GOST; UL; NOM 117

Marking: CE

Standards: EN 55011 class A group 2; IEC 61800-3 environments 1 category C3; IEC 61800-5-1; IEC 61800-3 environments 2 category C3; IEC 60721-3-3 class 3C1; UL Type 1; IEC 60721-3-3 class 3S2; IEC 61800-3

Assembly style: With heat sink

Electromagnetic compatibility: Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2; Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3; Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4; 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5; Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6; Voltage dips and interruptions immunity test conforming to IEC 61000-4-11

Regulation loop: Adjustable PI regulator

Speed accuracy: +/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn to Tn; +/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn

Ambient air temperature for storage: -25…70 °C

Unit Type of Package 1: PCE

Number of Units in Package 1: 1

Package 1 Height: 35.000 cm

Package 1 Width: 60.000 cm

Package 1 Length: 40.000 cm

Package 1 Weight: 17.391 kg

Unit Type of Package 2: P06

Number of Units in Package 2: 2

Package 2 Height: 75.000 cm

Package 2 Width: 60.000 cm

Package 2 Length: 80.000 cm

Package 2 Weight: 43.282 kg

REACh Regulation: Reference contains Substances of Very High Concern above the threshold

EU RoHS Directive: Pro-active compliance (Product out of EU RoHS legal scope)

Mercury free: Yes

China RoHS Regulation: X

RoHS exemption information: Yes

WEEE: The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins