Schneider-Electric
ATV310HU22N4E
Tariff code: 8504409090
Link to the manufacturers site: ATV310HU22N4E - Altivar 310 Easy frekvenciaváltó, 3f, 400V, 2,2kW
Main
range of product: Easy Altivar 310
product or component type: Variable speed drive
product specific application: Simple machine
assembly style: With heat sink
device short name: ATV310
network number of phases: Three phase
[Us] rated supply voltage: 380...460 V - 15...10 %
motor power kW: 2.2 kW
motor power hp: 3 hp
noise level: 50 dB
Complementary
product destination: Asynchronous motors
quantity per set: Set of 1
EMC filter: Without EMC filter
type of cooling: Integrated fan
supply frequency: 50/60 Hz +/- 5 %
communication port protocol: Modbus
connector type: RJ45 (on front face) for Modbus
physical interface: 2-wire RS 485 for Modbus
transmission frame: RTU for Modbus
transmission rate: 4800 bit/s; 9600 bit/s; 19200 bit/s; 38400 bit/s
number of addresses: 1…247 for Modbus
communication service: Read holding registers (03) 29 words; Write single register (06) 29 words; Write multiple registers (16) 27 words; Read/write multiple registers (23) 4/4 words; Read device identification (43)
line current: 7.2 A; 46.6 A
apparent power: 5.7 kVA; 31.2 kVA
prospective line Isc: 5 kA; 5 kA
continuous output current: 5.5 A at 4 kHz; 36 A at 4 kHz
maximum transient current: 8.3 A for 60 s; 39.6 A for 60 s
power dissipation in W: 66.32 W at In; 517.6 W at In
speed drive output frequency: 0.5…400 Hz
nominal switching frequency: 4 kHz
switching frequency: 2...12 kHz adjustable
speed range: 1…20
transient overtorque: 170…200 % of nominal motor torque depending on drive rating and type of motor
braking torque: Up to 150 % of nominal motor torque with braking resistor at high inertia; Up to 70 % of nominal motor torque without braking resistor
asynchronous motor control profile: Quadratic voltage/frequency ratio; Energy saving ratio; Sensorless flux vector control
motor slip compensation: Preset in factory; Adjustable
output voltage: 380...460 V three phase
electrical connection: Terminal, clamping capacity: 1.5...2.5 mm² (L1, L2, L3, PA/+, PB, U, V, W)
tightening torque: 0.8…1 N.m
insulation: Electrical between power and control
supply: Internal supply for reference potentiometer: 5 V (4.75…5.25 V)DC,
analogue input number: 1
analogue input type: Configurable current AI1 0...20 mA 250 Ohm; Configurable voltage AI1 0...10 V 30 kOhm; Configurable voltage AI1 0...5 V 30 kOhm
discrete input number: 4
discrete input type: Programmable LI1...LI4 24 V 18...30 V
discrete input logic: Negative logic (sink), > 16 V (state 0), 11 V (state 1)
sampling duration: 10 ms for analogue input; 20 ms, tolerance +/- 1 ms for logic input
linearity error: +/- 0.3 % of maximum value for analogue input
analogue output number: 1
analogue output type: AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bits; AO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits
discrete output number: 2
discrete output type: Logic output LO+, LO-; Protected relay output R1A, R1B, R1C 1 C/O
minimum switching current: 5 mA at 24 V DC for logic relay
maximum switching current: 2 A at 250 V AC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay; 2 A at 30 V DC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay; 3 A at 250 V AC on resistive load cos phi = 1 L/R = 0 ms for logic relay; 4 A at 30 V DC on resistive load cos phi = 1 L/R = 0 ms for logic relay
acceleration and deceleration ramps: U; S; Linear from 0...999.9 s
braking to standstill: By DC injection,
protection type: Line supply overvoltage; Line supply undervoltage; Overcurrent between output phases and earth; Overheating protection; Short-circuit between motor phases; Against input phase loss in three-phase; Thermal motor protection via the drive by continuous calculation of I²t
frequency resolution: Analog input: converter A/D, 10 bits; Display unit: 0.1 Hz
time constant: 20 ms +/- 1 ms for reference change
operating position: Vertical +/- 10 degree
height: 143 mm
width: 105 mm
depth: 151 mm
net weight: 1.1 kg
Environment
electromagnetic compatibility: Electrical fast transient/burst immunity test - test level: level 4 conforming to EN/IEC 61000-4-4; Electrostatic discharge immunity test - test level: level 3 conforming to EN/IEC 61000-4-2; Immunity to conducted disturbances - test level: level 3 conforming to EN/IEC 61000-4-6; Radiated radio-frequency electromagnetic field immunity test - test level: level 3 conforming to EN/IEC 61000-4-3; Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11; Surge immunity test - test level: level 3 conforming to EN/IEC 61000-4-5
standards: EN/IEC 61800-3; EN/IEC 61800-3
IP degree of protection: IP20 without blanking plate on upper part; IP40 top
pollution degree: 2 conforming to EN/IEC 61800-5-1
environmental characteristic: Dust pollution resistance class 3S2 conforming to EN/IEC 60721-3-3; Chemical pollution resistance class 3C3 conforming to EN/IEC 60721-3-3
shock resistance: 15 gn conforming to EN/IEC 60068-2-27 for 11 ms
relative humidity: 5…95 % without condensation conforming to IEC 60068-2-3; 5…95 % without dripping water conforming to IEC 60068-2-3
ambient air temperature for storage: -25…70 °C
ambient air temperature for operation: -10…55 °C without derating; 55…60 °C protective cover from the top of the drive removed with current derating 2.2 % per °C
operating altitude:
Offer Sustainability
Sustainable offer status: Green Premium product
REACh Regulation: Reference contains Substances of Very High Concern above the threshold
EU RoHS Directive: Compliant
Mercury free: Yes
RoHS exemption information: Yes
China RoHS Regulation: X
Environmental Disclosure: ENVPEP2007007EN
Circularity Profile: ENVEOLI2007007EN
WEEE: The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins
© 2018 Alplan Kft.