Schneider-Electric
ATV312H075N4

range of product: Altivar 312

product or component type: Variable speed drive

product destination: Asynchronous motors

product specific application: Simple machine

assembly style: With heat sink

component name: ATV312

motor power kW: 0.75 kW

motor power hp: 1 hp

[Us] rated supply voltage: 380...500 V - 15...10 %

supply frequency: 50...60 Hz - 5...5 %

network number of phases: 3 phases

line current: 3.6 A at 380 V, Isc = 5 kA; 2.7 A at 500 V

EMC filter: Integrated

apparent power: 2.4 kVA

maximum transient current: 3.5 A for 60 s

power dissipation in W: 41 W at nominal load

speed range: 1…50

asynchronous motor control profile: Sensorless flux vector control with PWM type motor control signal; Factory set : constant torque

electrical connection: Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm² AWG 14; L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 5 mm² AWG 10

supply: Internal supply for logic inputs: 19...30 V 100 mA, protection type: overload and short-circuit protection; Internal supply for reference potentiometer (2.2 to 10 kOhm): 10...10.8 V 10 mA, protection type: overload and short-circuit protection

communication port protocol: CANopen; Modbus

IP degree of protection: IP20 on upper part without cover plate; IP21 on connection terminals; IP31 on upper part; IP41 on upper part

option card: Communication card for CANopen daisy chain; Communication card for DeviceNet; Communication card for Fipio; Communication card for Modbus TCP; Communication card for Profibus DP

supply voltage limits: 323…550 V

prospective line Isc: 5 kA

continuous output current: 2.3 A at 4 kHz

output frequency: 0…500 Hz

nominal switching frequency: 4 kHz

switching frequency: 2...16 kHz adjustable

transient overtorque: 170…200 % of nominal motor torque

braking torque: 150 % during 60 s with braking resistor; 100 % with braking resistor continuously; 150 % without braking resistor

regulation loop: Frequency PI regulator

motor slip compensation: Adjustable; Automatic whatever the load; Suppressable

output voltage: <= power supply voltage

tightening torque: Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6: 0.6 N.m; L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 1.2 N.m

insulation: Electrical between power and control

analogue input number: 3

analogue input type: AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance: 30000 Ohm; AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 Ohm; AI3 configurable current 0...20 mA, impedance: 250 Ohm

sampling duration: AI1, AI2, AI3: 8 ms analog; LI1...LI6: 4 ms discrete

response time: AOV, AOC 8 ms for analog; R1A, R1B, R1C, R2A, R2B 8 ms for discrete

linearity error: +/- 0.2 % for output

analogue output number: 1

analogue output type: AOC configurable current: 0...20 mA, impedance: 800 Ohm, resolution: 8 bits; AOV configurable voltage: 0...10 V, impedance: 470 Ohm, resolution: 8 bits

discrete input logic: Logic input not wired (LI1...LI4), < 13 V (state 1); Negative logic (source) (LI1...LI6), > 19 V (state 0); Positive logic (source) (LI1...LI6), < 5 V (state 0), > 11 V (state 1)

discrete output number: 2

discrete output type: Configurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles; Configurable relay logic: (R2A, R2B) NC - 100000 cycles

minimum switching current: R1-R2 10 mA at 5 V DC

maximum switching current: R1-R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 ms; R1-R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 ms; R1-R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 ms; R1-R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms

discrete input number: 6

discrete input type: (LI1...LI6) programmable at 24 V, 0…100 mA for PLC, impedance: 3500 Ohm

acceleration and deceleration ramps: S, U or customized; Linear adjustable separately from 0.1 to 999.9 s

braking to standstill: By DC injection

protection type: Input phase breaks: drive; Line supply overvoltage and undervoltage safety circuits: drive; Line supply phase loss safety function, for three phases supply: drive; Motor phase breaks: drive; Overcurrent between output phases and earth (on power up only): drive; Overheating protection: drive; Short-circuit between motor phases: drive; Thermal protection: motor

insulation resistance: >= 500 mOhm 500 V DC for 1 minute

local signalling: 1 LED (red) for drive voltage; Four 7-segment display units for CANopen bus status

time constant: 5 ms for reference change

frequency resolution: Analog input: 0.1...100 Hz; Display unit: 0.1 Hz

connector type: 1 RJ45 for Modbus/CANopen

physical interface: RS485 multidrop serial link

transmission frame: RTU

transmission rate: 10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen; 4800, 9600 or 19200 bps for Modbus

number of addresses: 1…127 for CANopen; 1…247 for Modbus

number of drive: 127 for CANopen; 31 for Modbus

marking: CE

operating position: Vertical +/- 10 degree

height: 143 mm

width: 107 mm

depth: 152 mm

net weight: 1.8 kg

network frequency: 47.5...63 Hz

dielectric strength: 2410 V DC between earth and power terminals; 3400 V AC between control and power terminals

electromagnetic compatibility: 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5; Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4; Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2; Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3

standards: IEC 61800-3; IEC 61800-5-1

product certifications: NOM; C-Tick; CSA; UL; DNV; GOST

pollution degree: 2

protective treatment: TC

vibration resistance: 1 gn (f= 13…150 Hz) conforming to EN/IEC 60068-2-6; 1.5 mm (f= 3…13 Hz) conforming to EN/IEC 60068-2-6

shock resistance: 15 gn for 11 ms conforming to EN/IEC 60068-2-27

relative humidity: 5…95 % without condensation conforming to IEC 60068-2-3; 5…95 % without dripping water conforming to IEC 60068-2-3

ambient air temperature for storage: -25…70 °C

ambient air temperature for operation: -10…50 °C without derating (with protective cover on top of the drive); -10…60 °C with derating factor (without protective cover on top of the drive)

operating altitude: <= 1000 m without derating; 1000...3000 m with current derating 1 % per 100 m

Sustainable offer status: Green Premium product

REACh Regulation: Reference contains Substances of Very High Concern above the threshold

EU RoHS Directive: Pro-active compliance (Product out of EU RoHS legal scope)

Mercury free: Yes

RoHS exemption information: Yes

China RoHS Regulation: X

Environmental Disclosure: ENVPEP110706EN

Circularity Profile: ENVEOLI100203EN

WEEE: The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins